How to Fix System Restore error 0x81000204 on Windows 10

If when you attempt to perform System Restore on your Windows 10 device and experience the System Restore error 0x81000204, then this post is proposed to support you. In this post, we will give the most appropriate solutions you can attempt to effectively resolve this issue.

Fix System Restore error 0x81000204

Fix System Restore error 0x81000204

If you’re confronted with this issue, you can attempt our suggested solutions plot underneath in no specific request and check whether that assists with settling the issue.

1] Run CHKDSK

To run CHKDSK, do the accompanying:

Press Windows key + R to conjure the Run discourse.

In the Run exchange box, type cmd and afterward press CTRL + SHIFT + ENTER to open Command Prompt in administrator/raised mode.

In the order prompt window, type the order underneath and hit Enter.

chkdsk /x /f /r

You will get the accompanying message:

Chkdsk cannot run because the volume is in use by another process. Would you like to schedule this volume to be checked the next time the system restarts? (Y/N).

After CHKDSK finishes, verify whether the issue is settled.

2] Run SFC filter

System File Checker is a utility in Microsoft Windows that permits users to filter for and restore corruption in Windows system files.

This solution expects you to run the SFC filter and subsequently, have a go at running System Restore again and check whether it finishes effectively without the error 0x81000204.

If the issue is uncertain, continue with the following solution.

3] Perform DISM examine

Sending Image Servicing and Management (DISM.exe) comes incorporated with Windows 10 and is accessible through the order line or from Windows PowerShell – which can be used to support and plan Windows pictures, including those used for Windows PE, Windows Recovery Environment (Windows RE) and Windows Setup. DISM can be used to support a Windows picture (.wim) or a virtual hard disk (.vhd or .vhdx).

[insert page=’windows-10-video_tdr_failure-atikmpag-sys’ display=’excerpt’]

This solution expects you to perform DISM output and afterward retry the system restore operation. If the methodology fizzles with a similar error, continue with the following solution.

4] Use Windows Command Prompt

Open the Windows 10 Command Prompt and execute the accompanying orders in the provided request:

reg delete “HKLM\\SOFTWARE\\Policies\\Microsoft\\Windows NT\\SystemRestore” /v “DisableSR” /f

reg delete “HKLM\\SOFTWARE\\Policies\\Microsoft\\Windows NT\\SystemRestore” /v “DisableConfig” /f

reg add “HKLM\\Software\\Microsoft\\Windows NT\\CurrentVersion\\SPP\\Clients” /v ” {09F7EDC5-294E-4180-AF6A-FB0E6A0E9513}” /t REG_MULTI_SZ /d “1” /f

schtasks /Change /TN “Microsoft\\Windows\\SystemRestore\\SR” /Enable

vssadmin Resize ShadowStorage /For=C: /On=C: /Maxsize=25GB

sc config wbengine start= demand

sc config swprv start= demand

sc config vds start= demand

sc config VSS start= demand

Restart the system and attempt now.

5] Reset the Repository

To do so follows these steps:

  1. Boot into Safe Mode without systems administration and open an order prompt as administrator.
  2. Now Type net stop winmgmt and hit Enter.
  3. This will stop the Windows Management Instrumentation Service
  4. Next go to C:\Windows\System32\wbem
  5. Rename the repository folder to repositoryold
  6. Restart.

Again open an order prompt as administrator, type the accompanying and hit Enter:

net stop winmgmt

Next, type the accompanying and hit Enter:

winmgmt /resetRepository

Restart and check whether you can make a System Restore Point physically.

6] Run System Restore in Safe Mode or Clean Boot State

Boot into Safe Mode and check whether you make a system restore point or restore to an earlier restore point. Ordinarily, non-Microsoft administrations or Drivers can meddle with the best possible functioning of System Restore. On the other hand, you could likewise execute a Clean Boot and check whether you can get the system restore working.

[insert page=’download-windows-10-os-insider-build-20h2-final-release-october-2020-kb4577063-os-build-19042-541′ display=’excerpt’]

7] Use an outsider Backup programming

This solution just involves you use any of the outsider Imaging, Backup, and Recovery Software for Windows 10 equipped for doing likewise as the System Restore utility.

8] Perform Reset This PC, Cloud Reset or Repair Windows 10

If the issue is as yet uncertain, it’s most probably because of some sort of system corruption that can’t be settled conventionally. For this situation, the applicable solution here is that you can attempt Reset This PC, or Cloud Reset to reset each window component. You may likewise attempt to Repair Windows 10 using Installation Media if all else fails.

Leave a Comment